| View previous topic :: View next topic |
| Author |
Message |
surfcitylocal
Joined: 19 Nov 2005
Posts: 926
Location: Surf City SoCal
|
| Posted: 8/13/08 5:49PM Post subject: DIY: Replacing Gen 1 xB door handles |
|
|
This DIY will explain how to remove the factory xB door handles and replace them with after market door handles. Please follow all directions and remember as with all DIY threads, if you break it don't blame me.
First you will need to remove the door panels from the car. If you don't know how to do this here are a few quick shots.
Remove the Phillips head screws from the grab handle, the door latch handle and the area to the front of the panel near the door jam.
This part is not required but I do it to make the job easier. Remove the black triangle piece of plastic above the door panel.
Just pull and it will come off.
Grasp the door panel at the lower left corner and pull outwards.
Continue to pull around the edge of the door panel until all anchors have been released and the door panel can now be lifted up and away from the door.
Disconnect the electrical leads for the power windows and the stock stereo speaker wiring if you are still using it.
Pull back the factory plastic liner being careful not to tear it, you will be able to see the door handle from the inside.
There are two rods connected to the front door handles, these will need to be removed. There are yellow plastic holders keeping the rods attached. By pulling the plastic keepers off you will be able to remove the rods from their mounting holes on the door handle. They can be a little tough to pull so take your time.
There are two 10 mm bolts holding the door handle in place. Remove these bolts and the door handle slides right out.
Installation is the reverse of the removal.
The finished product...
The back door handles are a beeeeeyotch to do. Let me just say that it goes something like this.
Remove the door panels.
You will see one 10mm bolt holding on the rear door handle. There is another one but you won't be able to see it. You can best reach it by placing your arm through the lower panel opening and feeling your way to the bolt with a 10mm combination wrench. Once you loosen the bolt, push on the door handle from the outside and use your fingers to remove the bolt. It's not an easy task and may require you to use a different method. That's just the one that worked for us. |
|
| Back to top |
|
evosky
Joined: 28 Mar 2006
Posts: 1998
|
| Posted: 8/13/08 5:59PM Post subject: |
|
|
| niceee. good writeup. this needs to be stickied. |
|
| Back to top |
|
Metro273
Joined: 12 Feb 2005
Posts: 3485
Location: The House Music Mecca
|
| Posted: 8/13/08 6:01PM Post subject: |
|
|
| Nice write up and even better with pics! Those chrome handles look good on your ride... :clap: |
|
| Back to top |
|
surfcitylocal
Joined: 19 Nov 2005
Posts: 926
Location: Surf City SoCal
|
| Posted: 8/13/08 6:09PM Post subject: |
|
|
Metro273 wrote: Nice write up and even better with pics! Those chrome handles look good on your ride... :clap:
Thanks, that's not my ride though. That belongs to Dooby. I just did the handles for him. Mine is the PW.
|
|
| Back to top |
|
SuperMario6582
Joined: 31 Jan 2005
Posts: 1830
Location: ~*SoCal 951/909*~
|
| Posted: 8/13/08 8:49PM Post subject: |
|
|
| nice write up taz. i could have used it when i replaced mine. haha! you're right about the rears. they were a pain to take off. i got a scar on my right thumb now thanks to them. oh well. hahaha! |
|
| Back to top |
|
surfcitylocal
Joined: 19 Nov 2005
Posts: 926
Location: Surf City SoCal
|
| Posted: 8/13/08 9:03PM Post subject: |
|
|
| I found out on Club xB that if you remove the striker plate on the rear doors it gives you a clear shot at the nut. Wish I had known that before. =) |
|
| Back to top |
|
cherry-8
Joined: 12 Jun 2007
Posts: 45
Location: Northern Virginia
|
| Posted: 8/15/08 7:07AM Post subject: |
|
|
Nice writeup. I replaced a front on a Camry the other week and it was a bit of a bear. The procedure was pretty much the same. I take it you swapped the lock cylinders into the new latches?
Nice to see a Salsa Red box. Makes my heart flutter.
Cheers, |
|
| Back to top |
|
greenguyshrek
Joined: 03 Jan 2005
Posts: 691
|
| Posted: 8/15/08 7:18AM Post subject: |
|
|
| nice write up. alot of people could use thsi |
|
| Back to top |
|
surfcitylocal
Joined: 19 Nov 2005
Posts: 926
Location: Surf City SoCal
|
| Posted: 8/15/08 7:34AM Post subject: |
|
|
cherry-8 wrote: Nice writeup. I replaced a front on a Camry the other week and it was a bit of a bear. The procedure was pretty much the same. I take it you swapped the lock cylinders into the new latches?
Nice to see a Salsa Red box. Makes my heart flutter.
Cheers,
Yes we swapped the lock cylinders to the new handles.
FYI: That's not a salsa red, it's 2007 Ford Mustang Red. You gotta see it in person. It was originally TCM. |
|
| Back to top |
|
Just1n
Joined: 04 Apr 2007
Posts: 859
Location: www.ScionApocalypse.com
|
| Posted: 8/18/08 12:14PM Post subject: |
|
|
| Nice write up Taz... |
|
| Back to top |
|
TerrorCrew
Joined: 24 Apr 2006
Posts: 36
Location: San Diego
|
| Posted: 8/18/08 7:32PM Post subject: |
|
|
| yeah good write up! :clap: |
|
| Back to top |
|
| |